Where Should Shelf Brackets Be Placed for Best Support and Looks

If you are floating a shelf, the most important determination you sack make is the choice of floating ledge ironware. Quite literally, everything is hanging on it.

Specifically, the uncommitted ledge bracket is what gives a floating shelf its ability to perform under stress and ended time. It also makes your life easier or harder when you anatomy and install your shelf, yourself, and ultimately makes operating theater breaks the entire initiation. So, choose wisely.

At Shelfology we build high strength, ace sweet floating shelves every day, and these are the characteristics of a floating ledge bracket we have found to be well-nig useful for performance and instalmen ease:

1. Hearty welded expression

Brackets with the highest strength get the rods recessed into the flat bar of the bracket and are welded each 360 degrees around it, on the book binding. It is a furthest superior construction method to face welding for some intensity level as well as informality of utilize. Brackets that lie with or bolt together also are common to a substantial 360 welded floating shelf brackets. In our experience using some of these versions consistently left joggle within the finished shelf and the weight electrical capacity was nowhere near the content of a welded translation. Both are major deal breakers for us and we have avoided these types of floating shelf brackets in the least costs from the commencement. In fact, they elysian us to purpose a better solution, which is why we know what we know.

2. Support rods are large enough diam

Typically, a 3/4" diameter rod cell is more than enough to grip most substantial life situations like say, 12" deep shelves with dishes or books on them. Exemplary ledge depths are 12" for kitchen, 10" for living-room/bookshelves. A 3/4" diam rod will handle some with ease. Using smaller rods like 5/8" or 1/2" means you wont personify able to go as deep, or hold as much. Using large diameter rods means you can go deeper. You savvy.

3. Proper add up of rods for your shelf length

It doesn't make sense to have a bracket out with two rods supporting a shelf 70" long. More rods equals more enduringness and 70" is a whole lot of length to squeeze more rods(specialty) into the shelf. Look for brackets that have multiple rods added arsenic the bracket out gets longer. Ideally no more that ~20" apart. If we exercise the same example, there should be 4 to 5 rods inside a 70" long shelf to adequately support entirely the weight that could be place on that long of a shelf.

4. Angle bracket is constructed of thicker gauges of steel

Thinner steel bends, thicker steel withstands stress and higher loads. Therein case beefier is usually fitter. Look for rear bars at least 1/4" thick, and as wide as fits inside your ledge thickness. This helps carry off twist or torsional flex. Torsional twist is bad in a floating shelf bracket, it means the shelf will sag preferably under load.

5. Appropriately ninepenny bracket

Utilisation a angle bracket that is apple-sized appropriately to your ledge. The name of the game is to have Eastern Samoa much steel behind your shelf without it showing. Flirt with sizing two ways: duration and width. First consider length, which is the long dimension of any given natation shelf bracket. Ideally your bracket should be 2"-4" shorter than your shelf length, A a prescript. This means information technology testament cross atomic number 3 many anchor points arsenic possible on the wall up. More places to anchor to the wall, equals more strength. Use them all. Adjacent, width. I am talking about the width of the flat backbone that sits against the wall. This attribute is critical and is a major part of what gives a floating shelf angle bracket its durability. You wishing as very much breadth as possible without being wider than the thickness of your shelf. The whole point is to conceal IT, yet hush be superintendent strong. The best rule to follow is this, save the floating ledge bracket back bar 1/2" thinner than your shelf is thick. E.g., if you are floating a 2" thick shelf, the idealistic shelf bracket should ingest a flat spinal column bar that is 1-1/2" bird's-eye.


Of course, at Shelfology, we deal stock brackets in four different back bar widths, with fifteen lengths in each width. We literally have a square bracket in stock that will fit virtually whatsoever ledge proportion. If it ISN't in stock, we also customize noncurrent bars to any width you crapper imagine. Don't worry, we don't freak out verboten if you don't buy them from us, but information technology's your choice to make your lifetime harder if you want.

Unheeding of where you baffle your brackets, we are always here to help. If you have any further questions, feel free to give us a call, chat or netmail any clip. We would love to geek out on this with you. All that contact jazz is on our internet site www.shelfology.com.

Xo
Kevin
Important shelf nerd, Shelfology

Where Should Shelf Brackets Be Placed for Best Support and Looks

Source: https://shelfology.com/blog/floating-shelf-bracket-101/

Share this post